Skip to main content

Posts

Showing posts with the label Repair guide
Resistor inspection and repair After some fixed resistors are open or their resistance increases, their surface will have apparent changes such as cracks, pins disconnect, or blackened color. At this time, we can use an intuitive check to confirm whether they are good or bad.  If the appearance of the suspected resistor is normal, you need to test it with a multimeter to determine whether it is normal. Measuring resistance with a multimeter is divided into two methods: in-circuit detection and non-in-circuit detection. In-circuit detection is to directly measure the resistance of the suspected resistance on the circuit board to determine whether it is consistent with the nominal value. Non-in-circuit measurement is to measure the resistance after removing the resistance from the circuit board or suspending a pin. 1. Detect fixed-resistance (1) First, write down the nominal value. If it is a color ring resistor, first find out its resistance value according to the color ring. If you don
Which components of the Antminer T17 hash board are easily damaged ? T17 hash board (BHB07601) has a total of 30 BM1397AG chips . It adopts double-sided heat dissipation (there are heat sinks on both sides of the hash board). And during long-term continuous operation, some components will easily fail. The easily damaged electronic components of the hash board are described as follows. Schematic diagram of T17 hash board: front, the heat sinks have been removed, this type of heat sink  is soldered to the chip by solder paste, visible ASIC chip. Schematic diagram of T17 hash board: back, the heat sink is fixed on the hash board with soldering paste.   Easily damaged part 1: ASIC chip (BM1397AG) There are a total of 30 BM1397AG chips on the whole board. They are distributed under the front heat sink and connected to the heat sink through the thermosetting adhesive. In daily maintenance, ASIC chip damage is widespread. After the ASIC chip is damaged, the miner will have no hashrate or low
How to detect the capacitor on the repair circuit board? 1. Detect electrolytic capacitor The steps for measuring electrolytic capacitance with a pointer multimeter are as follows: First, use an electric soldering iron to remove the electrolytic capacitor to be tested from the circuit board. Remove the capacitor from the board Second, observe whether the electrolytic capacitor under test has obvious problems such as cracks, broken pins, burnt black, and liquid leakage. If there is, it means that the capacitor has failed. Third, wipe clean the pins of the electrolytic capacitor to be tested and discharge them with tweezers. Clean the Pins and discharge the capacitor Fourth, select the "R*10" gear of the multimeter, and short-circuit the two test leads for zero-return calibration. Short-circuit the two leads Fifth, connect the red test lead of the multimeter to the negative pole of the capacitor and the black test lead to the positive pole of the capacitor and observe the point
How to inspect and repair inductors? The magnetic rod inductors or magnetic loop inductors in the circuit board are mainly used in various power supply circuits. The magnetic rod/magnetic ring inductor can be measured with a digital multimeter or a pointer multimeter. For accurate measurement, the inductor can be measured with an open circuit. Use a digital multimeter to detect the inductor in the circuit board: (1)  First, disconnect the power supply of the circuit board, and then observe the magnetic bar inductor to be tested to see if the inductor is damaged, whether it is burnt, soldered, or the coil is deformed. If there is, the inductor has been damaged. The figure below shows a magnetic bar inductor to be tested. (2)  If the appearance of the magnetic rod inductor to be tested is not damaged, solder the magnetic toroidal inductor to be tested from the circuit board with an electric soldering iron, and clean the pins at both ends of the magnetic toroidal inductor, and clean the r

What Are the Common Procedures for Repairing Antminer L3+ Hash Board?

Common repair process 1. Routine inspection: First of all, visually inspect the hash board to be repaired to observe whether there is any displacement, deformation, or scorching of the small heat sink? If any, you must deal with it first; if the small heat sink is displaced, remove it first, wash off the original glue, and re-adhesive after the repair is passed. Secondly, after the visual inspection is no problem, the impedance of each voltage domain can be tested first to detect whether there is a short circuit or an open circuit. If found, it must be dealt with first. Thirdly, check whether the voltage of each voltage domain reaches 0.8V, and the voltage difference of each voltage domain shall not exceed 0.05V. If the voltage of a certain voltage domain is too high or too low, the circuits in the adjacent voltage domain generally have abnormal phenomena. Need to investigate the reason first. 2. After the routine test is no problem (the short-circuit test of the general routine test i

How to Check And Replace Miner Fan and Power Supply fan?

 How to check and replace miner fan and Power supply fan? Miner fan or PSU fan is almost the most vulnerable component because of the continuous work of miners. High-strength and high-speed working methods can easily cause damage to its bearings and internal coils. When the fan is damaged, the miner or PSU will lose heat dissipation and cannot work or damage the chip. Therefore, regular inspection and replacement of bad fans is an essential job of maintaining miners. Both ASIC miners and GPU miners use a large number of cooling fans. Depending on the device model, the fan specifications used are also different. Normally, the most common fan sizes are: 4cm, 6cm, 12cm, 14cm. The standard voltage is 12V, the current is 0.27A to 7.2A, and the power cord is 2 to 6 pins. The specific size of the fan to be selected needs to be determined according to the device. When these fans fail, it isn't easy to detect from the appearance because one piece of equipment is equipped with 2 to 4 fans. W